452 lines
17 KiB
TeX
452 lines
17 KiB
TeX
% -*- mode: latex; TeX-master: "Vorbis_I_spec"; -*-
|
|
%!TEX root = Vorbis_I_spec.tex
|
|
\section{Residue setup and decode} \label{vorbis:spec:residue}
|
|
|
|
\subsection{Overview}
|
|
|
|
A residue vector represents the fine detail of the audio spectrum of
|
|
one channel in an audio frame after the encoder subtracts the floor
|
|
curve and performs any channel coupling. A residue vector may
|
|
represent spectral lines, spectral magnitude, spectral phase or
|
|
hybrids as mixed by channel coupling. The exact semantic content of
|
|
the vector does not matter to the residue abstraction.
|
|
|
|
Whatever the exact qualities, the Vorbis residue abstraction codes the
|
|
residue vectors into the bitstream packet, and then reconstructs the
|
|
vectors during decode. Vorbis makes use of three different encoding
|
|
variants (numbered 0, 1 and 2) of the same basic vector encoding
|
|
abstraction.
|
|
|
|
|
|
|
|
\subsection{Residue format}
|
|
|
|
Residue format partitions each vector in the vector bundle into chunks,
|
|
classifies each chunk, encodes the chunk classifications and finally
|
|
encodes the chunks themselves using the the specific VQ arrangement
|
|
defined for each selected classification.
|
|
The exact interleaving and partitioning vary by residue encoding number,
|
|
however the high-level process used to classify and encode the residue
|
|
vector is the same in all three variants.
|
|
|
|
A set of coded residue vectors are all of the same length. High level
|
|
coding structure, ignoring for the moment exactly how a partition is
|
|
encoded and simply trusting that it is, is as follows:
|
|
|
|
\begin{itemize}
|
|
\item Each vector is partitioned into multiple equal sized chunks
|
|
according to configuration specified. If we have a vector size of
|
|
\emph{n}, a partition size \emph{residue\_partition\_size}, and a total
|
|
of \emph{ch} residue vectors, the total number of partitioned chunks
|
|
coded is \emph{n}/\emph{residue\_partition\_size}*\emph{ch}. It is
|
|
important to note that the integer division truncates. In the below
|
|
example, we assume an example \emph{residue\_partition\_size} of 8.
|
|
|
|
\item Each partition in each vector has a classification number that
|
|
specifies which of multiple configured VQ codebook setups are used to
|
|
decode that partition. The classification numbers of each partition
|
|
can be thought of as forming a vector in their own right, as in the
|
|
illustration below. Just as the residue vectors are coded in grouped
|
|
partitions to increase encoding efficiency, the classification vector
|
|
is also partitioned into chunks. The integer elements of each scalar
|
|
in a classification chunk are built into a single scalar that
|
|
represents the classification numbers in that chunk. In the below
|
|
example, the classification codeword encodes two classification
|
|
numbers.
|
|
|
|
\item The values in a residue vector may be encoded monolithically in a
|
|
single pass through the residue vector, but more often efficient
|
|
codebook design dictates that each vector is encoded as the additive
|
|
sum of several passes through the residue vector using more than one
|
|
VQ codebook. Thus, each residue value potentially accumulates values
|
|
from multiple decode passes. The classification value associated with
|
|
a partition is the same in each pass, thus the classification codeword
|
|
is coded only in the first pass.
|
|
|
|
\end{itemize}
|
|
|
|
|
|
\begin{center}
|
|
\includegraphics[width=\textwidth]{residue-pack}
|
|
\captionof{figure}{illustration of residue vector format}
|
|
\end{center}
|
|
|
|
|
|
|
|
\subsection{residue 0}
|
|
|
|
Residue 0 and 1 differ only in the way the values within a residue
|
|
partition are interleaved during partition encoding (visually treated
|
|
as a black box--or cyan box or brown box--in the above figure).
|
|
|
|
Residue encoding 0 interleaves VQ encoding according to the
|
|
dimension of the codebook used to encode a partition in a specific
|
|
pass. The dimension of the codebook need not be the same in multiple
|
|
passes, however the partition size must be an even multiple of the
|
|
codebook dimension.
|
|
|
|
As an example, assume a partition vector of size eight, to be encoded
|
|
by residue 0 using codebook sizes of 8, 4, 2 and 1:
|
|
|
|
\begin{programlisting}
|
|
|
|
original residue vector: [ 0 1 2 3 4 5 6 7 ]
|
|
|
|
codebook dimensions = 8 encoded as: [ 0 1 2 3 4 5 6 7 ]
|
|
|
|
codebook dimensions = 4 encoded as: [ 0 2 4 6 ], [ 1 3 5 7 ]
|
|
|
|
codebook dimensions = 2 encoded as: [ 0 4 ], [ 1 5 ], [ 2 6 ], [ 3 7 ]
|
|
|
|
codebook dimensions = 1 encoded as: [ 0 ], [ 1 ], [ 2 ], [ 3 ], [ 4 ], [ 5 ], [ 6 ], [ 7 ]
|
|
|
|
\end{programlisting}
|
|
|
|
It is worth mentioning at this point that no configurable value in the
|
|
residue coding setup is restricted to a power of two.
|
|
|
|
|
|
|
|
\subsection{residue 1}
|
|
|
|
Residue 1 does not interleave VQ encoding. It represents partition
|
|
vector scalars in order. As with residue 0, however, partition length
|
|
must be an integer multiple of the codebook dimension, although
|
|
dimension may vary from pass to pass.
|
|
|
|
As an example, assume a partition vector of size eight, to be encoded
|
|
by residue 0 using codebook sizes of 8, 4, 2 and 1:
|
|
|
|
\begin{programlisting}
|
|
|
|
original residue vector: [ 0 1 2 3 4 5 6 7 ]
|
|
|
|
codebook dimensions = 8 encoded as: [ 0 1 2 3 4 5 6 7 ]
|
|
|
|
codebook dimensions = 4 encoded as: [ 0 1 2 3 ], [ 4 5 6 7 ]
|
|
|
|
codebook dimensions = 2 encoded as: [ 0 1 ], [ 2 3 ], [ 4 5 ], [ 6 7 ]
|
|
|
|
codebook dimensions = 1 encoded as: [ 0 ], [ 1 ], [ 2 ], [ 3 ], [ 4 ], [ 5 ], [ 6 ], [ 7 ]
|
|
|
|
\end{programlisting}
|
|
|
|
|
|
|
|
\subsection{residue 2}
|
|
|
|
Residue type two can be thought of as a variant of residue type 1.
|
|
Rather than encoding multiple passed-in vectors as in residue type 1,
|
|
the \emph{ch} passed in vectors of length \emph{n} are first
|
|
interleaved and flattened into a single vector of length
|
|
\emph{ch}*\emph{n}. Encoding then proceeds as in type 1. Decoding is
|
|
as in type 1 with decode interleave reversed. If operating on a single
|
|
vector to begin with, residue type 1 and type 2 are equivalent.
|
|
|
|
\begin{center}
|
|
\includegraphics[width=\textwidth]{residue2}
|
|
\captionof{figure}{illustration of residue type 2}
|
|
\end{center}
|
|
|
|
|
|
\subsection{Residue decode}
|
|
|
|
\subsubsection{header decode}
|
|
|
|
Header decode for all three residue types is identical.
|
|
\begin{programlisting}
|
|
1) [residue\_begin] = read 24 bits as unsigned integer
|
|
2) [residue\_end] = read 24 bits as unsigned integer
|
|
3) [residue\_partition\_size] = read 24 bits as unsigned integer and add one
|
|
4) [residue\_classifications] = read 6 bits as unsigned integer and add one
|
|
5) [residue\_classbook] = read 8 bits as unsigned integer
|
|
\end{programlisting}
|
|
|
|
\varname{[residue\_begin]} and
|
|
\varname{[residue\_end]} select the specific sub-portion of
|
|
each vector that is actually coded; it implements akin to a bandpass
|
|
where, for coding purposes, the vector effectively begins at element
|
|
\varname{[residue\_begin]} and ends at
|
|
\varname{[residue\_end]}. Preceding and following values in
|
|
the unpacked vectors are zeroed. Note that for residue type 2, these
|
|
values as well as \varname{[residue\_partition\_size]}apply to
|
|
the interleaved vector, not the individual vectors before interleave.
|
|
\varname{[residue\_partition\_size]} is as explained above,
|
|
\varname{[residue\_classifications]} is the number of possible
|
|
classification to which a partition can belong and
|
|
\varname{[residue\_classbook]} is the codebook number used to
|
|
code classification codewords. The number of dimensions in book
|
|
\varname{[residue\_classbook]} determines how many
|
|
classification values are grouped into a single classification
|
|
codeword. Note that the number of entries and dimensions in book
|
|
\varname{[residue\_classbook]}, along with
|
|
\varname{[residue\_classifications]}, overdetermines to
|
|
possible number of classification codewords.
|
|
If \varname{[residue\_classifications]}\^{}\varname{[residue\_classbook]}.dimensions
|
|
exceeds \varname{[residue\_classbook]}.entries, the
|
|
bitstream should be regarded to be undecodable.
|
|
|
|
Next we read a bitmap pattern that specifies which partition classes
|
|
code values in which passes.
|
|
|
|
\begin{programlisting}
|
|
1) iterate [i] over the range 0 ... [residue\_classifications]-1 {
|
|
|
|
2) [high\_bits] = 0
|
|
3) [low\_bits] = read 3 bits as unsigned integer
|
|
4) [bitflag] = read one bit as boolean
|
|
5) if ( [bitflag] is set ) then [high\_bits] = read five bits as unsigned integer
|
|
6) vector [residue\_cascade] element [i] = [high\_bits] * 8 + [low\_bits]
|
|
}
|
|
7) done
|
|
\end{programlisting}
|
|
|
|
Finally, we read in a list of book numbers, each corresponding to
|
|
specific bit set in the cascade bitmap. We loop over the possible
|
|
codebook classifications and the maximum possible number of encoding
|
|
stages (8 in Vorbis I, as constrained by the elements of the cascade
|
|
bitmap being eight bits):
|
|
|
|
\begin{programlisting}
|
|
1) iterate [i] over the range 0 ... [residue\_classifications]-1 {
|
|
|
|
2) iterate [j] over the range 0 ... 7 {
|
|
|
|
3) if ( vector [residue\_cascade] element [i] bit [j] is set ) {
|
|
|
|
4) array [residue\_books] element [i][j] = read 8 bits as unsigned integer
|
|
|
|
} else {
|
|
|
|
5) array [residue\_books] element [i][j] = unused
|
|
|
|
}
|
|
}
|
|
}
|
|
|
|
6) done
|
|
\end{programlisting}
|
|
|
|
An end-of-packet condition at any point in header decode renders the
|
|
stream undecodable. In addition, any codebook number greater than the
|
|
maximum numbered codebook set up in this stream also renders the
|
|
stream undecodable. All codebooks in array [residue\_books] are
|
|
required to have a value mapping. The presence of codebook in array
|
|
[residue\_books] without a value mapping (maptype equals zero) renders
|
|
the stream undecodable.
|
|
|
|
|
|
|
|
\subsubsection{packet decode}
|
|
|
|
Format 0 and 1 packet decode is identical except for specific
|
|
partition interleave. Format 2 packet decode can be built out of the
|
|
format 1 decode process. Thus we describe first the decode
|
|
infrastructure identical to all three formats.
|
|
|
|
In addition to configuration information, the residue decode process
|
|
is passed the number of vectors in the submap bundle and a vector of
|
|
flags indicating if any of the vectors are not to be decoded. If the
|
|
passed in number of vectors is 3 and vector number 1 is marked 'do not
|
|
decode', decode skips vector 1 during the decode loop. However, even
|
|
'do not decode' vectors are allocated and zeroed.
|
|
|
|
Depending on the values of \varname{[residue\_begin]} and
|
|
\varname{[residue\_end]}, it is obvious that the encoded
|
|
portion of a residue vector may be the entire possible residue vector
|
|
or some other strict subset of the actual residue vector size with
|
|
zero padding at either uncoded end. However, it is also possible to
|
|
set \varname{[residue\_begin]} and
|
|
\varname{[residue\_end]} to specify a range partially or
|
|
wholly beyond the maximum vector size. Before beginning residue
|
|
decode, limit \varname{[residue\_begin]} and
|
|
\varname{[residue\_end]} to the maximum possible vector size
|
|
as follows. We assume that the number of vectors being encoded,
|
|
\varname{[ch]} is provided by the higher level decoding
|
|
process.
|
|
|
|
\begin{programlisting}
|
|
1) [actual\_size] = current blocksize/2;
|
|
2) if residue encoding is format 2
|
|
3) [actual\_size] = [actual\_size] * [ch];
|
|
4) [limit\_residue\_begin] = minimum of ([residue\_begin],[actual\_size]);
|
|
5) [limit\_residue\_end] = minimum of ([residue\_end],[actual\_size]);
|
|
\end{programlisting}
|
|
|
|
The following convenience values are conceptually useful to clarifying
|
|
the decode process:
|
|
|
|
\begin{programlisting}
|
|
1) [classwords\_per\_codeword] = [codebook\_dimensions] value of codebook [residue\_classbook]
|
|
2) [n\_to\_read] = [limit\_residue\_end] - [limit\_residue\_begin]
|
|
3) [partitions\_to\_read] = [n\_to\_read] / [residue\_partition\_size]
|
|
\end{programlisting}
|
|
|
|
Packet decode proceeds as follows, matching the description offered earlier in the document.
|
|
\begin{programlisting}
|
|
1) allocate and zero all vectors that will be returned.
|
|
2) if ([n\_to\_read] is zero), stop; there is no residue to decode.
|
|
3) iterate [pass] over the range 0 ... 7 {
|
|
|
|
4) [partition\_count] = 0
|
|
|
|
5) while [partition\_count] is less than [partitions\_to\_read]
|
|
|
|
6) if ([pass] is zero) {
|
|
|
|
7) iterate [j] over the range 0 .. [ch]-1 {
|
|
|
|
8) if vector [j] is not marked 'do not decode' {
|
|
|
|
9) [temp] = read from packet using codebook [residue\_classbook] in scalar context
|
|
10) iterate [i] descending over the range [classwords\_per\_codeword]-1 ... 0 {
|
|
|
|
11) array [classifications] element [j],([i]+[partition\_count]) =
|
|
[temp] integer modulo [residue\_classifications]
|
|
12) [temp] = [temp] / [residue\_classifications] using integer division
|
|
|
|
}
|
|
|
|
}
|
|
|
|
}
|
|
|
|
}
|
|
|
|
13) iterate [i] over the range 0 .. ([classwords\_per\_codeword] - 1) while [partition\_count]
|
|
is also less than [partitions\_to\_read] {
|
|
|
|
14) iterate [j] over the range 0 .. [ch]-1 {
|
|
|
|
15) if vector [j] is not marked 'do not decode' {
|
|
|
|
16) [vqclass] = array [classifications] element [j],[partition\_count]
|
|
17) [vqbook] = array [residue\_books] element [vqclass],[pass]
|
|
18) if ([vqbook] is not 'unused') {
|
|
|
|
19) decode partition into output vector number [j], starting at scalar
|
|
offset [limit\_residue\_begin]+[partition\_count]*[residue\_partition\_size] using
|
|
codebook number [vqbook] in VQ context
|
|
}
|
|
}
|
|
|
|
20) increment [partition\_count] by one
|
|
|
|
}
|
|
}
|
|
}
|
|
|
|
21) done
|
|
|
|
\end{programlisting}
|
|
|
|
An end-of-packet condition during packet decode is to be considered a
|
|
nominal occurrence. Decode returns the result of vector decode up to
|
|
that point.
|
|
|
|
|
|
|
|
\subsubsection{format 0 specifics}
|
|
|
|
Format zero decodes partitions exactly as described earlier in the
|
|
'Residue Format: residue 0' section. The following pseudocode
|
|
presents the same algorithm. Assume:
|
|
|
|
\begin{itemize}
|
|
\item \varname{[n]} is the value in \varname{[residue\_partition\_size]}
|
|
\item \varname{[v]} is the residue vector
|
|
\item \varname{[offset]} is the beginning read offset in [v]
|
|
\end{itemize}
|
|
|
|
|
|
\begin{programlisting}
|
|
1) [step] = [n] / [codebook\_dimensions]
|
|
2) iterate [i] over the range 0 ... [step]-1 {
|
|
|
|
3) vector [entry\_temp] = read vector from packet using current codebook in VQ context
|
|
4) iterate [j] over the range 0 ... [codebook\_dimensions]-1 {
|
|
|
|
5) vector [v] element ([offset]+[i]+[j]*[step]) =
|
|
vector [v] element ([offset]+[i]+[j]*[step]) +
|
|
vector [entry\_temp] element [j]
|
|
|
|
}
|
|
|
|
}
|
|
|
|
6) done
|
|
|
|
\end{programlisting}
|
|
|
|
|
|
|
|
\subsubsection{format 1 specifics}
|
|
|
|
Format 1 decodes partitions exactly as described earlier in the
|
|
'Residue Format: residue 1' section. The following pseudocode
|
|
presents the same algorithm. Assume:
|
|
|
|
\begin{itemize}
|
|
\item \varname{[n]} is the value in
|
|
\varname{[residue\_partition\_size]}
|
|
\item \varname{[v]} is the residue vector
|
|
\item \varname{[offset]} is the beginning read offset in [v]
|
|
\end{itemize}
|
|
|
|
|
|
\begin{programlisting}
|
|
1) [i] = 0
|
|
2) vector [entry\_temp] = read vector from packet using current codebook in VQ context
|
|
3) iterate [j] over the range 0 ... [codebook\_dimensions]-1 {
|
|
|
|
4) vector [v] element ([offset]+[i]) =
|
|
vector [v] element ([offset]+[i]) +
|
|
vector [entry\_temp] element [j]
|
|
5) increment [i]
|
|
|
|
}
|
|
|
|
6) if ( [i] is less than [n] ) continue at step 2
|
|
7) done
|
|
\end{programlisting}
|
|
|
|
|
|
|
|
\subsubsection{format 2 specifics}
|
|
|
|
Format 2 is reducible to format 1. It may be implemented as an additional step prior to and an additional post-decode step after a normal format 1 decode.
|
|
|
|
|
|
Format 2 handles 'do not decode' vectors differently than residue 0 or
|
|
1; if all vectors are marked 'do not decode', no decode occurrs.
|
|
However, if at least one vector is to be decoded, all the vectors are
|
|
decoded. We then request normal format 1 to decode a single vector
|
|
representing all output channels, rather than a vector for each
|
|
channel. After decode, deinterleave the vector into independent vectors, one for each output channel. That is:
|
|
|
|
\begin{enumerate}
|
|
\item If all vectors 0 through \emph{ch}-1 are marked 'do not decode', allocate and clear a single vector \varname{[v]}of length \emph{ch*n} and skip step 2 below; proceed directly to the post-decode step.
|
|
\item Rather than performing format 1 decode to produce \emph{ch} vectors of length \emph{n} each, call format 1 decode to produce a single vector \varname{[v]} of length \emph{ch*n}.
|
|
\item Post decode: Deinterleave the single vector \varname{[v]} returned by format 1 decode as described above into \emph{ch} independent vectors, one for each outputchannel, according to:
|
|
\begin{programlisting}
|
|
1) iterate [i] over the range 0 ... [n]-1 {
|
|
|
|
2) iterate [j] over the range 0 ... [ch]-1 {
|
|
|
|
3) output vector number [j] element [i] = vector [v] element ([i] * [ch] + [j])
|
|
|
|
}
|
|
}
|
|
|
|
4) done
|
|
\end{programlisting}
|
|
|
|
\end{enumerate}
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|